I am trying to install ORACLE 11gR2 RAC on CentOS 5.5 .
when run root.sh on first node. I am gettign 2/3 failed command lines but the end went successful
======================================================================= ohasd is starting ADVM/ACFS is not supported on centos-release-5-5.el5.centos ... add nodeapps -n perflabhp03 -A perflabhp03-vip/255.255.254.0/eth0 on node=perflabhp03 ... failed ... PRCR-1001 : Resource ora.net1.network does not exist add scan=perflab-cluster-scan ... failed, Configure Oracle Grid Infrastructure for a Cluster ... failed ... 'UpdateNodeList' was successful. =========================================================================
Because of this output, when see the ./crsctl stat res -t , it showing LISTENER offline for perflahp03, and I can not see any status line for "perflabhp03-vip " and "Scan-listener".
Do I need to reinstall the entire cluster setup because of VIP issue?
I'm trying to create a ASM disk using oracleasm.I created list the disk (using oracleasm), but the view V$ASM_DISK and ASMCMD (lsdsk command) can't see it..Look:
Normally ASMlib/oracleasm is used to prepare the disks for ASM. I just wonder, besides this tool, is there any other GUI based tool to use for preparing the ASM disks?
i have installed oracle 11gr2 on centos 4.7,,but after that when i invoke command for startup in sqlplus for sys user it shows an insufficient privileges error. and what are the post installation tasks? is the database installed also?what is the name of database and where is it?
I install oracle 11g2 on centos, in prerequisite checks step ,oracle database show this failed "Oracle Restart integrity Failed", I don't know what should i do ?
In the OWB mapping,I needed to transfer data in lob table1 to lob table2 .Both tables are in 2 different schema.The table1 has blob and clob columns.The table 2 has same structure like table 1 and the table 2 is empty.
I have created the mapping and connected directly from the source table to the target table.Also , I have created a error table for the target table table. As for the data rule method,I customized the error table to log the non unique rows.
When I start validating the mapping . I got the following error
VLD-3200 Deduplicator cannot contain LOB type columns
How to log the error in error table for transferring lob type table1 to lob type table 2
I installed Oracle Express on my Windows 2003 Enterprise server. And right off the bat I cannot connect to it via command line. I have googled and read many sites, but am still getting the same error, no matter what I do. I am newbie again (was a DBA in 1990...when I used to have the same error and fix it in seconds...not sure why this problem still lingers in Oracle) so most likely I am overlooking something. Below are my tnsnames.ora and liserner.ora files.
I am having a rough time trying to install Oacle 10.2.0.3.0 on Z/OS 1.7.
Since my installation does not allow us to use X Windows nor Telnet, I have been forced to try to install using a silent install response file. The install does not seem to get very far and throws out an informational message, but no actual errors. All this is being done via OMVS on USS (UNIX system services).
The message I am getting is:
INFO: INFO: Unable to read the list of homes from the inventory.
I think it may be a permissions issue, and the support people are pursuing this avenue as well, but so far, no concrete answers.
I execute ./runInstaller -silent -responsefile <my responsefile.rsp>
I wanted to install oracle 9i in windows xp.My configuration is intel celeron,2.5ghz,256 mb ram ,5.5 gb of free hard disk space.I do no anything about the oracle ,was trying to install oracle on redhat 9 but had some problems..I just wanted the step by step documentation of installing oracle 9i in xp.
I install oracle 10 g but I don't remember password . so I then remove oracle 10 g by select Universal Installer and click Deinstall and then reinstall but I can't reinstall because I don't remove/delete oracle_home I then delete folder in path C:Oracle and reinstall Question
1.in this remove oracle 10 g method true or wrong if wrong , How effect on my computer 2.why after reinstall my computer is very slow.
we have RAC database on two node here on windows server 2008 unfortunately today morning my one my one node os crash its on windows server 2008 my other node its working ok so my database is accessible so i just want to ask if i install again this os on node -1 system so i just want to install only again crs only.because my database is accessible through my other node-2
I have dell inspiron 15R model N5010 laptop, I have windows 7 64 bit operating system, intel i5 processor, 4 gb ram,500gb hdd. how does install oracle 10g in my system.
Oracle database 10g Express Edition...I need to install "Oracle database 10g Express Edition" with different database name example dev but it is taking default name that is XE and there is no option come during installation where i can put the name of database as per my desire.
And also explain why we use "Oracle database 10g Express Edition" instead of Oracle database 10g. what is the meaning of Express Edition.
, We are doing a fresh setup on new hardware. On the old hardware Oracle is installed on the SAN and all data files are on there as well. Our new blades are Dell M620 with 2 mirrored 500GB drives and our SAN is Dell Complaint Storage and Complaint TLS Controller. The SAN uses hybrid SSD storage so it keeps the most used data cached.
I'm feeling it would be best to install the Oracle Server on the SAN. On top of that we have a single 620GB fusion IO NAND flash card in the mix. I am still researching the configuration of that.
I need to build a new server for my Oracle 10gR2 due to compatibilities with the new storage system that we have purchased, this server will run RHEL5 x64 and will replace a RHEL4 x64. Since doing an upgrade poses greater risk as the upgrade may fail, I am thinking about building a new server with RHEL5 x64 doing all the config/tuning and then simply running the same Oracle installation (after a full backup) which I was running on the RHEL4 x64.
For this to work I will just need to mount the SAN drives on the new server but and this may be a big but, considering that some versions of some libraries will change do I need to relink anything in my Oracle? I have never manually relinked anything but Oracle may have done so during the initial install.
I'm trying to install Grid Infrastructure for Oracle RAC 11g. I followed each step of pre installation tasks, but when I run run Installer it blocks without any error message.
What I see on my shell is this: ./runInstaller Avvio di Oracle Universal Installer in corso...
Verifica dello spazio Temp: deve essere maggiore di 120 MB. Effettivi 17276 MB Superato Verifica dello spazio di swap: deve essere maggiore di 150 MB. Effettivi 23999 MB Superato Verifica del monitor: deve essere configurato per visualizzare almeno 256 colori. Effettivo 16777216 Superato Preparazione per l'avvio di Oracle Universal Installer da /tmp/OraInstall2012-01-11_03-35-57AM. Attendere...[oracle@ssts2cora1 grid]$
Everything seems ok. But the window of oracle installation does not appear. The java process is active:
but it does nothing!! Nothing appears to me. I attach the log file generated by the installation process.
Using paramFile: /home/software_ssts/grid/install/oraparam.ini
Checking Temp space: must be greater than 120 MB. Actual 17276 MB Passed Checking swap space: must be greater than 150 MB. Actual 23999 MB Passed Checking monitor: must be configured to display at least 256 colors. Actual 16777216 Passed
The commandline for unzip:
/home/software_ssts/grid/install/unzip -qqqo ../stage/Components/oracle.jdk/1.5.0.17.0/1/DataFiles/\*.jar -d /tmp/OraInstall2012-01-11_03-35-57AM Verr� utilizzato il valore di umask '022' disponibile in oraparam.ini
Execvp of the child jre : the cmdline is /tmp/OraInstall2012-01-11_03-35-57AM/jdk/jre/bin/java, and the argv is /tmp/OraInstall2012-01-11_03-35-57AM/jdk/jre/bin/java -Doracle.installer.library_loc=/tmp/OraInstall2012-01-11_03-35-57AM/oui/lib/linux -Doracle.installer.oui_loc=/tmp/OraInstall2012-01-11_03-35-57AM/oui -Doracle.installer.bootstrap=TRUE -Doracle.installer.startup_location=/home/software_ssts/grid/install -Doracle.installer.jre_loc=/tmp/OraInstall2012-01-11_03-35-57AM/jdk/jre [code].......
I just installed WEBLOGIC server on linux with oracle forms 11g builder and report builder on the server.
On the client machine , i have probleme to intsall oracle forms 11g , in one of the steps it asks me to enter the absolute location of server weblogic , i enter the location of the weblogic on the server , but it dosent' work. is it mean that i have to install the weblogic on the client machine too!! if not to install forms builder 11g on the client
Is oracle 10g availble for Windows 7, I downloaded oracle 10g from ORACLE'S website. The name of the file is "10203_ vista_ w2k8_ x86_ production_ db.zip" but when I m installing it, I m getting error at the very beginning regarding the system requirements failure.
below is the message which i receive at the PRODUCT-SPECIFIC PREREQUISITE CHECK ====================================== Checking operating system requirements ...
Expected result: One of 5.0,5.1,5.2,6.0 Actual Result: 6.1 Check complete. The overall result of this check is: Failed <<<< Problem: Oracle Database 10g is not certified on the current operating system. Recommendation: Make sure you are installing the software on the correct platform. ======================================================================= [code]....
I am trying to install oracle database 11g.2 on windows 7. bu I received error in configuration database step.error is attached to this topic. installed database on windows so far.the emca text is below .....
----- @echo off setlocal set OH=E:appproduct11.2.0dbhome set JRE_JAVA=%OH%jdkjreinjava
We are trying to develop one excel sheet from PL/SQL. But the requirement is that we want specific colors and fonts for specific rows and columns. For that purpose, we are using Excel Document Type. But we are getting error that Excel Document Type should be declared.How can we get rid of this error?